Paint Systems. All Paint Systems Are Detailed At The End Of This Specification. For Colour Requirements Refer To Specification. General Requirements For Workshop Application. All Structural Steel Work Shall Be Prepared For Painting And Have The Paint System Applied Before Erection, Unless Specifically Directed To Do So. In All Cases Where Surfaces Will Be Inaccessible After Shop Assembly, They Shall Be Prepared And Have The Paint System Applied Before Assembly Is Carried Out. Drying Time Between Successive Coats Shall Be As Recommended By The Paint Manufacturer. All Known Field Weld Areas Shall Be Given The Specified Abrasive Blast Surface Preparation. Inorganic Zinc Silicate Shall Be Applied To The Contact Surfaces Of Friction Grip Joints Ensuring That The Coating Allows For The Development Of The Slip Factor Prescribed In AS 1511. The Contents Of Paint Cans Shall Be Thoroughly Stirred Before Being Poured Into Paint Pots And Shall Be Thinned In Only The Specified Quantity In Accordance With The Manufacturer's Instructions. The Paint Manufacturer Directions For Preparation And Application Of Coating Shall Be Rigorously Followed To Ensure That The Durability Of The Coating System Is Not Impaired By Malpractice.
General Requirements Pertaining to Workshop Application. All Structural Metal Work Shall Be ready for Painting And have The Colouring System Used before Erection, Unless Exclusively Directed to do so. In Many Cases Where Surfaces Are going to be Inaccessible Immediately after Shop Set up, they will have The Colouring System Used Before Set up can be Completed. Drying Between Successive Coats Will is As Recommended from the Paint Maker. All Field Weld Areas need a Coarse Blast Exterior Preparation beforehand. Colours that are substandard by any means or perhaps not in accordance with the actual specification will not be used. Only colours from the manufacturer can be utilised. The majority of crime must be removed, or additional procedures will likely be required before starting area preparation. Colour containers can be thinned by using the instructions.
Many layers might be utilized simply by spraying, except wherever any excess of spray is likely to have an impact on areas. In all conditions, a Normandy representative will accept the use of every coating ahead of its install.
These types of outcomes are going to be compared relative to standard 3894 Elements 10, 11 & 12 (Appendix A) to ensure conformity. All materials can be cleaned as per standard 1627 Portion 3 "Metallic surfaces prep". Many colours have for the actual risk instructions plus the manufacturer's instructions. In all of the conditions wherever areas will turn into a hard surface, many people will be ready and have the actual colour process ahead of time to gain access, and it may become extremely hard. Equipment within a given location is to stay there unless otherwise specified.
An electrical engineer controls the terms of acceptability when an inspection is needed, to the extent that treatment or making before progressing. Toxins consist of residuals along with all soluble salts and need to be taken away by high pressure water blasting. The conventional connection with exterior preparation will be Category 3 as outlined in standard 1627, Portion 3. Consider hand cleaning to bring all materials in line with Category 3. Almost all materials without particles need to be cleaned up before work starts. Before any exterior change occurring, all products and services for items of equipment may undergo deterioration due to approaches that are not thoroughly masked.
Area preparation shall not be performed during damp conditions, once the comparative moisture exceeds 85% or the pre heat is less than 3 degrees below the dew level. The exterior needs to be tested for salts and pH readings. The quantity of sales may not go beyond 6g/cm 3. Almost all weld splatter cannot be taken away by blasting and will require mechanical assistance. All wild areas are washed out with solvent to remove impurities related to welding flux, paying attention to other toxins and defects. Wherever possible, wooden supports in contact with painted items during transport and storage shall be covered with a soft material such as rubber to minimize damage to the coating. Hessian fabric shall be used during transportation between the painted item and holding down chains to prevent damage to the paint coating.
General Requirements Pertaining to Workshop Application. All Structural Metal Work Shall Be ready for Painting And have The Colouring System Used before Erection, Unless Exclusively Directed to do so. In Many Cases Where Surfaces Are going to be Inaccessible Immediately after Shop Set up, they will have The Colouring System Used Before Set up can be Completed. Drying Between Successive Coats Will is As Recommended from the Paint Maker. All Field Weld Areas need a Coarse Blast Exterior Preparation beforehand. Colours that are substandard by any means or perhaps not in accordance with the actual specification will not be used. Only colours from the manufacturer can be utilised. The majority of crime must be removed, or additional procedures will likely be required before starting area preparation. Colour containers can be thinned by using the instructions.
Many layers might be utilized simply by spraying, except wherever any excess of spray is likely to have an impact on areas. In all conditions, a Normandy representative will accept the use of every coating ahead of its install.
These types of outcomes are going to be compared relative to standard 3894 Elements 10, 11 & 12 (Appendix A) to ensure conformity. All materials can be cleaned as per standard 1627 Portion 3 "Metallic surfaces prep". Many colours have for the actual risk instructions plus the manufacturer's instructions. In all of the conditions wherever areas will turn into a hard surface, many people will be ready and have the actual colour process ahead of time to gain access, and it may become extremely hard. Equipment within a given location is to stay there unless otherwise specified.
An electrical engineer controls the terms of acceptability when an inspection is needed, to the extent that treatment or making before progressing. Toxins consist of residuals along with all soluble salts and need to be taken away by high pressure water blasting. The conventional connection with exterior preparation will be Category 3 as outlined in standard 1627, Portion 3. Consider hand cleaning to bring all materials in line with Category 3. Almost all materials without particles need to be cleaned up before work starts. Before any exterior change occurring, all products and services for items of equipment may undergo deterioration due to approaches that are not thoroughly masked.
Area preparation shall not be performed during damp conditions, once the comparative moisture exceeds 85% or the pre heat is less than 3 degrees below the dew level. The exterior needs to be tested for salts and pH readings. The quantity of sales may not go beyond 6g/cm 3. Almost all weld splatter cannot be taken away by blasting and will require mechanical assistance. All wild areas are washed out with solvent to remove impurities related to welding flux, paying attention to other toxins and defects. Wherever possible, wooden supports in contact with painted items during transport and storage shall be covered with a soft material such as rubber to minimize damage to the coating. Hessian fabric shall be used during transportation between the painted item and holding down chains to prevent damage to the paint coating.
No comments:
Post a Comment